검색결과
-
[특집-기술위원회] TC 212 - 의료 실험실 및 체외 진단 시스템(Medical laboratories and in vitro diagnostic systems)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 등이 있다.ISO/TC 212 의료 실험실 및 체외 진단 시스템(Medical laboratories and in vitro diagnostic systems)과 관련된 기술위원회는 TC 210, TC 211과 마찬가지로 1994년 결성됐다. 사무국은 미국 표준협회(American National Standards Institute, ANSI)에서 맡고 있다.위원회는데이비드 스테리(Mr David Sterry)가 책임지고 있다. 현재 의장은 헤수스 루에다 로드리게스(Mr Jesus Rueda Rodriguez)이며 임기는 2027년말까지다. ISO 기술 프로그램 관리자는 이사벨 베가(Ms Isabelle Vega), ISO 편집 관리자는 발레리아 아가넨노네(Ms Valeria Agamennone) 등이다.범위는 의료 실험실 및 체외 진단 시스템 분야의 표준화 및 지침이다. 여기에는 품질 관리, 분석 전후 절차, 분석 성능, 실험실 안전, 참조 시스템 및 품질 보증 등이 포함된다.단, ISO/TC 176에서 다루는 일반 품질 관리 표준, ISO/TC 210에서 다루는 의료기기 품질 관리 표준, ISO/TC 334 참조 자료 위원회(REMCO)에서 다루는 참조 자료 지침, ISO 적합성 평가 위원회(CASCO)에서 다루는 적합성 평가 지침 등은 제외된다현재 ISO/TC 212 사무국의 직접적인 책임 하에 발행된 표준은 47개며 ISO/TC 212 사무국의 직접적인 책임 하에 개발 중인 표준은 23개다. 참여하고 있는 회원은 41개국, 참관 회원은 33개국이다.□ ISO/TC 212 사무국의 직접적인 책임 하에 발행된 표준 47개 중 15개 목록▷ISO 4307:2021 Molecular in vitro diagnostic examinations — Specifications for pre-examination processes for saliva — Isolated human DNA▷ISO/TS 5798:2022 In vitro diagnostic test systems — Requirements and recommendations for detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) by nucleic acid amplification methods▷ISO 15189:2022 Medical laboratories — Requirements for quality and competence▷ISO 15190:2020 Medical laboratories — Requirements for safety▷ISO 15193:2009 In vitro diagnostic medical devices — Measurement of quantities in samples of biological origin — Requirements for content and presentation of reference measurement procedures▷ISO 15194:2009 In vitro diagnostic medical devices — Measurement of quantities in samples of biological origin — Requirements for certified reference materials and the content of supporting documentation▷ISO 15195:2018 Laboratory medicine — Requirements for the competence of calibration laboratories using reference measurement procedures▷ISO 15197:2013 In vitro diagnostic test systems — Requirements for blood-glucose monitoring systems for self-testing in managing diabetes mellitus▷ISO 15198:2004 Clinical laboratory medicine — In vitro diagnostic medical devices — Validation of user quality control procedures by the manufacturer▷ISO 16256:2021 Clinical laboratory testing and in vitro diagnostic test systems — Broth micro-dilution reference method for testing the in vitro activity of antimicrobial agents against yeast fungi involved in infectious diseases▷ISO/TS 16782:2016 Clinical laboratory testing — Criteria for acceptable lots of dehydrated Mueller-Hinton agar and broth for antimicrobial susceptibility testing▷ISO 17511:2020 In vitro diagnostic medical devices — Requirements for establishing metrological traceability of values assigned to calibrators, trueness control materials and human samples▷ISO/TS 17518:2015 Medical laboratories — Reagents for staining biological material — Guidance for users▷ISO 17593:2022 Clinical laboratory testing and in vitro medical devices — Requirements for in vitro monitoring systems for self-testing of oral anticoagulant therapy▷ISO 17822:2020 In vitro diagnostic test systems — Nucleic acid amplification-based examination procedures for detection and identification of microbial pathogens — Laboratory quality practice guide□ ISO/TC 212 사무국의 직접적인 책임 하에 개발 중인 표준 23개 중 15개 목록▷ISO/DTS 5441 Competence requirements for biorisk management advisors▷ISO/DIS 5649 Medical laboratories — Concepts and specifications for the design, development, implementation, and use of laboratory-developed tests▷ISO/AWI TS 7446 ISO 35001 — Biorisk management for laboratories and other related organisations — Implementation guidance▷ISO/CD TS 7552-1 Specifications for pre-examination processes for circulating tumor cells (CTCs) in venous whole blood — Part 1: Isolated RNA▷ISO/CD TS 7552-2 Specifications for pre-examination processes for circulating tumor cells (CTCs) in venous whole blood — Part 2: Isolated DNA▷ISO/CD TS 7552-3 Specifications for pre-examination processes for circulating tumor cells (CTCs) in venous whole blood — Part 3: Preparations for analytical CTC staining▷ISO/AWI TS 8219 Sequencing and clinical application to infectious diseases▷ISO/DIS 15193 In vitro diagnostic medical devices — Requirements for reference measurement procedures▷ISO/DIS 15194 In vitro diagnostic medical devices — Requirements for certified reference materials and the content of supporting documentation▷ISO/CD TS 16766.2 Manufacturers’considerations for in vitro diagnostic medical devices in a public health crisis▷ISO/AWI TS 18701 Molecular in vitro diagnostic examinations — Specificationsfor pre-examination processes for human specimens — Isolated microbiome DNA▷ISO/AWI TS 18702 Molecular in vitro diagnostic examinations — Specifications for pre-examination processes for exosomes and other extracellular vesicles in venous whole blood — DNA, RNA and proteins▷ISO/AWI 18703 Molecular in vitro diagnostic examinations — Specifications for pre-examination processes for venous whole blood — Isolated circulating cell free RNA from plasma▷ISO/CD 18704 Molecular in vitro diagnostic examinations — Specifications for pre-examination processes for urine and other body fluids — Isolated cell free DNA▷ISO/DIS 21474-3 In vitro diagnostic medical devices — Multiplex molecular testing for nucleic acids — Part 3: Interpretation and reports
-
[특집-기술위원회] TC 211 - 지리정보/지리학(Geographic information/Geomatics)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 등이 있다.ISO/TC 211지리정보/지리학(Geographic information/Geomatics)과 관련된 기술위원회는 TC 210과 마찬가지로 1994년 결성됐다. 사무국은 스웨덴 국립표준청(Svenska institutet för standarder, SIS)에서 맡고 있다.위원회는 마츠 올린(Mr Mats Åhlin)가 책임지고 있다. 현재 의장은 피터 파슬로(Mr Peter Parslow)이며 임기는 2024년말까지다. ISO 기술 프로그램 관리자는 하킴 음킨시(Mr Hakim Mkinsi), ISO 편집 관리자는 앨리슨 레이드 자몬드(Ms Alison Reid-Jamond) 등이다.범위는 디지털 지리정보 분야의 표준화다. 지구와 관련된 위치와 직간접적으로 연관된 물체나 현상에 관한 정보에 대한 구조화된 표준 세트 확립을 목표로 하고 있다.지리 정보의 범위 내에서 이러한 표준은 데이터 관리를 위한 방법, 도구 및 서비스를 지정할 수 있다. 데이터 관리는 사용자 및 시스템을 위한 데이터 획득, 처리, 분석, 접근, 제시 및 출판이 포함된다.이 작업은 가능한 경우 정보 기술 및 데이터에 대한 적절한 표준과 연결되어야 하며 지리 데이터를 사용하는 부문별 응용 프로그램 개발을 위한 프레임워크를 제공해야 된다.현재 ISO/TC 211 사무국의 직접적인 책임 하에 발행된 표준은 97개며 ISO/TC 211 사무국의 직접적인 책임 하에 개발 중인 표준은 26개다. 참여하고 있는 회원은 38개국, 참관 회원은 35개국이다.□ ISO/TC 211 사무국의 직접적인 책임 하에 발행된 표준 97개 중 15개 목록▷ISO 6709:2022 Standard representation of geographic point location by coordinates▷ISO 19101-1:2014 Geographic information — Reference model — Part 1: Fundamentals▷ISO 19101-2:2018 Geographic information — Reference model — Part 2: Imagery▷ISO 19103:2015 Geographic information — Conceptual schema language▷ISO 19104:2016 Geographic information — Terminology▷ISO 19105:2022 Geographic information — Conformance and testing▷ISO 19106:2004 Geographic information — Profiles▷ISO 19107:2019 Geographic information — Spatial schema▷ISO 19108:2002 Geographic information — Temporal schema▷ISO 19108:2002/Cor 1:2006 Geographic information — Temporal schema — Technical Corrigendum 1▷ISO 19109:2015 Geographic information — Rules for application schema▷ISO 19110:2016 Geographic information — Methodology for feature cataloguing▷ISO 19111:2019 Geographic information — Referencing by coordinates▷ISO 19111:2019/Amd 1:2021 Geographic information — Referencing by coordinates — Amendment 1▷ISO 19111:2019/Amd 2:2023 Geographic information — Referencing by coordinates — Amendment 2□ ISO/TC 211 사무국의 직접적인 책임 하에 개발 중인 표준 26개 중 15개 목록▷ISO/DIS 19103 Geographic information — Conceptual schema language▷ISO/CD 19109 Geographic information — General feature model and rules for application schema▷ISO/AWI TR 19115-4 Geographic information – Metadata — Part 4: JSON schema implementation of metadata fundamentals▷ISO/DIS 19116 Geographic information — Positioning services▷ISO/AWI TR 19121 Geographic information — Imagery and gridded data▷ISO/AWI 19123-2 Geographic information — Schema for coverage geometry and functions — Part 2: Coverage implementation schema▷ISO/AWI TS 19123-4 Geographic information — Schema for coverage geometry and functions — Part 4: Tiling Schema▷ISO/AWI TS 19124-2 Geographic information — Calibration and validation of remote sensing data and derived products — Part 2: SAR▷ISO/AWI 19127 Geographic information — Geodetic register▷ISO/AWI TS 19130-2 Geographic information — Imagery sensor models for geopositioning — Part 2: SAR, InSAR, lidar and sonar▷ISO/CD 19135 Geographic information registration — Requirements▷ISO/DTS 19144-3 Geographic information — Classification systems — Part 3: Land Use Meta Language (LUML)▷ISO/DIS 19152-2 Geographic information — Land Administration Domain Model (LADM) — Part 2: Land registration▷ISO/FDIS 19152-3 Geographic information — Land Administration Domain Model (LADM) — Part 3: Marine georegulation▷ISO/DIS 19152-4 Geographic information — Land Administration Domain Model (LADM) — Part 4: Valuation information
-
[특집-기술위원회] TC 210 - 의료기기를 포함한 건강 목적 제품의 품질 관리 및 이에 상응하는 일반적인 측면(Quality management and corresponding general aspects for products with a health purpose including medical devices스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 등이 있다.ISO/TC 210 의료기기를 포함한 건강 목적 제품의 품질 관리 및 이에 상응하는 일반적인 측면(Quality management and corresponding general aspects for products with a health purpose including medical devices)과 관련된 기술위원회는 1994년 결성됐다. 사무국은 미국 표준협회(American National Standards Institute, ANSI)에서 맡고 있다.위원회는 아미르 어바우탈레브(Mr Amir Aboutaleb)가 책임지고 있다. 현재 의장은 스콧 A. 콜번(Mr Scott A. Colburn)이며 임기는 2025년말까지다. ISO 기술 프로그램 관리자는 키르시 실란데르-반 후넨(Mrs Kirsi Silander-van Hunen), ISO 편집 관리자는 클라우디아 루에제(Ms Claudia Lueje) 등이다.범위는 액체 및 가스용 커넥터를 포함하는 건강 목적의 제품에 대한 품질 관리 및 상응하는 일반적인 측면과 관련한 분야의 요구 사항 및 지침에 관한 표준화다.단, △ISO/TC 176에서 다루는 일반 품질 관리 표준 △의약품 및 의료 서비스에 대한 품질 관리 표준은 제외한다.참고로 건강 목적의 제품에는 의료 기기, 인접 제품(또는 액세서리라고도 할 수 있음) 및 의료 기기와 유사한 위험 프로필을 가진 제품을 포함해 건강과 관련된 사용을 위한 제품이 포함된다.현재 ISO/TC 210 사무국의 직접적인 책임 하에 발행된 표준은 30개며 ISO/TC 210 사무국의 직접적인 책임 하에 개발 중인 표준은 13개다. 참여하고 있는 회원은 39개국, 참관 회원은 28개국이다.□ ISO/TC 210 사무국의 직접적인 책임 하에 발행된 표준 30개 중 15개 목록▷ISO 13485:2016 Medical devices — Quality management systems — Requirements for regulatory purposes▷ISO 14971:2019 Medical devices — Application of risk management to medical devices▷ISO 15223-1:2021 Medical devices — Symbols to be used with information to be supplied by the manufacturer — Part 1: General requirements▷ISO 15223-2:2010 Medical devices — Symbols to be used with medical device labels, labelling, and information to be supplied — Part 2: Symbol development, selection and validation▷ISO 18250-1:2018 Medical devices — Connectors for reservoir delivery systems for healthcare applications — Part 1: General requirements and common test methods▷ISO 18250-3:2018 Medical devices — Connectors for reservoir delivery systems for healthcare applications — Part 3: Enteral applications▷ISO 18250-6:2019 Medical devices — Connectors for reservoir delivery systems for healthcare applications — Part 6: Neural applications▷ISO 18250-7:2018 Medical devices — Connectors for reservoir delivery systems for healthcare applications — Part 7: Connectors for intravascular infusion▷ISO 18250-8:2018 Medical devices — Connectors for reservoir delivery systems for healthcare applications — Part 8: Citrate-based anticoagulant solution for apheresis applications▷ISO/TR 20416:2020 Medical devices — Post-market surveillance for manufacturers▷ISO 20417:2021 Medical devices — Information to be supplied by the manufacturer▷ISO/TR 24971:2020 Medical devices — Guidance on the application of ISO 14971▷IEC 62304:2006 Medical device software — Software life cycle processes▷IEC 62304:2006/Amd 1:2015 Medical device software — Software life cycle processes — Amendment 1▷IEC 62366-1:2015 Medical devices — Part 1: Application of usability engineering to medical devices□ ISO/TC 210 사무국의 직접적인 책임 하에 개발 중인 표준 13개 목록▷ISO/WD TS 5137 Medical device maintenance management for healthcare delivery organizations▷ISO 15223-1:2021/AWI Amd 1 Medical devices — Symbols to be used with information to be supplied by the manufacturer — Part 1: General requirements — Amendment 1▷ISO/AWI 15223-2 Medical devices — Symbols to be used with medical device labels, labelling, and information to be supplied — Part 2: Symbol development, selection and validation▷ISO/AWI 18250-3 Medical devices — Connectors for reservoir delivery systems for healthcare applications — Part 3: Enteral applications▷ISO 18250-8:2018/AWI Amd 1 Medical devices — Connectors for reservoir delivery systems for healthcare applications — Part 8: Citrate-based anticoagulant solution for apheresis applications — Amendment 1▷ISO/CD 20417 Medical devices — Information to be supplied by the manufacturer▷ISO/AWI 23421 Medical devices — Terminology — Terms used in the field of quality management and corresponding general aspects for products with a health purpose including medical devices▷ISO/CD TS 24971-2 Medical devices — Guidance on the application of ISO 14971 — Part 2: Machine learning in artificial intelligence▷ISO/DIS 80369-1 Small-bore connectors for liquids and gases in healthcare applications — Part 1: General requirements▷ISO/FDIS 80369-2 Small-bore connectors for liquids and gases in healthcare applications — Part 2: Connectors for respiratory applications▷IEC/AWI 80369-5 Small-bore connectors for liquids and gases in healthcare applications — Part 5: Connectors for limb cuff inflation applications▷ISO/DIS 80369-6 Small bore connectors for liquids and gases in healthcare applications — Part 6: Connectors for neural applications▷ISO/FDIS 80369-20 Small-bore connectors for liquids and gases in healthcare applications — Part 20: Common test methods
-
[특집-기술위원회] TC 209 - 클린룸 및 관련 제어 환경(Cleanrooms and associated controlled environments)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 등이 있다.ISO/TC 209 클린룸 및 관련 제어 환경(Cleanrooms and associated controlled environments)과 관련된 기술위원회는 TC 207과 마찬가지로 1993년 결성됐다. 사무국은 미국 표준협회(American National Standards Institute, ANSI)에서 맡고 있다.위원회는 로버트 미엘케(Mr Robert Mielke)가 책임지고 있다. 현재 의장은 고든 엘리(Mr Gordon Ely)이며 임기는 2026년말까지다. ISO 기술 프로그램 관리자는 마호 타카하시(Mme Maho Takahashi), ISO 편집 관리자는 아룬 ABY 파라에카틸(Mr Arun ABY Paraecattil) 등이다.범위는 시설, 지속 가능성, 장비, 프로세스 및 운영과 관련된 기타 속성 및 특성 뿐 아니라 청결도를 제어하기 위한 클린룸 및 관련 제어 환경에 대한 표준화다.현재 ISO/TC 209 사무국의 직접적인 책임 하에 발행된 표준은 20개며 ISO/TC 209 사무국의 직접적인 책임 하에 개발 중인 표준은 3개다. 참여하고 있는 회원은 26개국, 참관 회원은 22개국이다.□ ISO/TC 209 사무국의 직접적인 책임 하에 발행된 표준 20개 중 15개 목록▷ISO 14644-1:2015 Cleanrooms and associated controlled environments — Part 1: Classification of air cleanliness by particle concentration▷ISO 14644-2:2015 Cleanrooms and associated controlled environments — Part 2: Monitoring to provide evidence of cleanroom performance related to air cleanliness by particle concentration▷ISO 14644-3:2019 Cleanrooms and associated controlled environments — Part 3: Test methods▷ISO 14644-4:2022 Cleanrooms and associated controlled environments — Part 4: Design, construction and start-up▷ISO 14644-5:2004 Cleanrooms and associated controlled environments — Part 5: Operations▷ISO 14644-7:2004 Cleanrooms and associated controlled environments — Part 7: Separative devices (clean air hoods, gloveboxes, isolators and mini-environments)▷ISO 14644-8:2022 Cleanrooms and associated controlled environments — Part 8: Assessment of air cleanliness by chemical concentration (ACC)▷ISO 14644-9:2022 Cleanrooms and associated controlled environments — Part 9: Assessment of surface cleanliness for particle concentration▷ISO 14644-10:2022 Cleanrooms and associated controlled environments — Part 10: Assessment of surface cleanliness for chemical contamination▷ISO 14644-12:2018 Cleanrooms and associated controlled environments — Part 12: Specifications for monitoring air cleanliness by nanoscale particle concentration▷ISO 14644-13:2017 Cleanrooms and associated controlled environments — Part 13: Cleaning of surfaces to achieve defined levels of cleanliness in terms of particle and chemical classifications▷ISO 14644-14:2016 Cleanrooms and associated controlled environments — Part 14: Assessment of suitability for use of equipment by airborne particle concentration▷ISO 14644-15:2017 Cleanrooms and associated controlled environments — Part 15: Assessment of suitability for use of equipment and materials by airborne chemical concentration▷ISO 14644-16:2019 Cleanrooms and associated controlled environments — Part 16: Energy efficiency in cleanrooms and separative devices▷ISO 14644-17:2021 Cleanrooms and associated controlled environments — Part 17: Particle deposition rate applications□ ISO/TC 209 사무국의 직접적인 책임 하에 개발 중인 표준 3개 목록▷ISO/AWI 14644-5 Cleanrooms and associated controlled environments — Part 5: Operations▷ISO/CD TS 14644-19 Cleanrooms and associated controlled environments — Part 19: General technical requirements of modular isolation units for emergency medical use▷ISO/AWI 14644-20 Cleanrooms and associated controlled environments — Part 20: Microbiological contamination control
-
[특집-기술위원회] TC 206 - 파인 세라믹(Fine ceramics)… 모든 형태의 파인 세라믹 재료 및 제품 분야 표준화스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~TC 186 △1984년 TC 188 △1985년 TC 189, TC 190, TC 191 △1988년 TC 192~TC 194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 등이 있다.ISO/TC 206 파인 세라믹(Fine ceramics)과 관련된 기술위원회는 TC 204, TC 205와 마찬가지로 1992년 결성됐다. 사무국은 일본 산업표준조사회(日本産業標準調査会, Japanese Industrial Standards Committee, JISC)에서 맡고 있다.위원회는 히로유키 미야자키(Dr Hiroyuki Miyazaki)가 책임지고 있다. 현재 의장은 이희수 교수(Prof Heesoo Lee)가 맡고 있다.ISO 기술 프로그램 관리자는 츄안유 추(Ms Chuanyu Zou), ISO 편집 관리자는 아룬 ABY 파라에카틸(Mr Arun ABY Paraecattil) 등이다.범위는 모든 형태의 파인 세라믹 재료 및 제품 분야 표준화다. 기계, 열, 화학, 전기, 자기, 광학 및 이들의 조합을 포함한 특정 기능 응용 분야를 위한 분말, 단일체, 코팅 및 복합재 등 모든 형태를 포함하고 있다. 파인 세라믹이라는 용어는 특정 기능적 특성을 지닌 고도로 가공된 고성능, 주로 비금속 무기 재료로 정의된다.참고로 파인 세라믹의 대체 용어는 고급 세라믹, 엔지니어링 세라믹, 테크니컬 세라믹 또는 고성능 세라믹이다. 파인 세라믹(Fine ceramics)은 절연체·내열재·구조재로 쓸수 있도록 고도기술로 개발된 새로운 세라믹을 말한다.현재 ISO/TC 206 사무국의 직접적인 책임 하에 발행된 표준은 156개며 ISO/TC 206 사무국의 직접적인 책임하에 개발 중인 표준은 32개다. 참여하고 있는 회원은 13개국, 참관 회원은 22개국이다.□ ISO/TC 206 사무국의 직접적인 책임 하에 발행된 표준 156개 중 15개 목록▷ISO 3169:2023 Fine ceramics (advanced ceramics, advanced technical ceramics) — Methods for chemical analysis of impurities in aluminium oxide powders using inductively coupled plasma-optical emission spectrometry▷ISO 3180:2023 Fine ceramics (advanced ceramics, advanced technical ceramics) — Methods for chemical analysis of calcium-phosphate-based powders for non-biomedical applications▷ISO 4825-1:2023 Fine ceramics (advanced ceramics, advanced technical ceramics) --Test method for thermal property measurements of metalized ceramic substrates — Part 1: Evaluation of thermal resistance for use in power modules▷ISO 5189:2023 Fine ceramics (advanced ceramics, advanced technical ceramics) — Methods for chemical analysis of metal impurities in silicon dioxide powders using inductively coupled plasma-optical emission spectrometry▷ISO 5618-1:2023 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for GaN crystal surface defects — Part 1: Classification of defects▷ISO 5712:2022 Fine ceramics (advanced ceramics, advanced technical ceramics) — Method for measuring the power generation characteristics of piezoelectric resonant devices for stand-alone power sources▷ISO 5722:2023 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for determining tensile and shear creep of ceramic adhesive▷ISO 5803:2023 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for determination of monoclinic phase in zirconia▷ISO/TS 6857:2024 Fine ceramics (advanced ceramics, advanced technical ceramics) — Physical properties of ceramic composites — Guidelines for determination of void and fibre contents in polished cross section by image analysis▷ISO 10676:2010 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for water purification performance of semiconducting photocatalytic materials by measurement of forming ability of active oxygen▷ISO 10677:2011 Fine ceramics (advanced ceramics, advanced technical ceramics) — Ultraviolet light source for testing semiconducting photocatalytic materials▷ISO 10678:2010 Fine ceramics (advanced ceramics, advanced technical ceramics) — Determination of photocatalytic activity of surfaces in an aqueous medium by degradation of methylene blue▷ISO 11894-1:2013 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for conductivity measurement of ion-conductive fine ceramics — Part 1: Oxide-ion-conducting solid electrolytes▷ISO 13124:2011 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for interfacial bond strength of ceramic materials▷ISO 13125:2013 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for antifungal activity of semiconducting photocatalytic materials□ ISO/TC 206 사무국의 직접적인 책임 하에 개발 중인 표준 32개 중 15개 목록▷ISO/CD 4255 Fine ceramics (advanced ceramics, advanced technical ceramics) — Mechanical properties of ceramic matrix composites at high temperature — Determination of axial tensile properties of tubes▷ISO/AWI 4825-2 Fine ceramics (advanced ceramics, advanced technical ceramics) --Test method for thermal property measurements of metalized ceramic substrates — Part 2: Evaluation of heat transfer characteristics for metalized ceramics substrate for power modules▷ISO/PRF 5618-2 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for GaN crystal surface defects — Part 2: Method for determining etch pit density▷ISO/CD 5770 Fine ceramics (advanced ceramics, advanced technical ceramics) — Relative method for determining thermal conductivity of ceramic coatings▷ISO/DIS 10678 Fine ceramics (advanced ceramics, advanced technical ceramics) — Determination of photocatalytic activity of surfaces in an aqueous medium by degradation of methylene blue▷ISO/AWI 10820 Fine ceramics (advanced ceramics, advanced technical ceramics) — Ultraviolet irradiation equipment using UV-A LEDs and optical radiometry for performance test of semiconducting photocatalytic materials▷ISO/DIS 14544 Fine ceramics (advanced ceramics, advanced technical ceramics) — Mechanical properties of ceramic composites at high temperature — Determination of compressive properties▷ISO/DIS 14574 Fine ceramics (advanced ceramics, advanced technical ceramics) — Mechanical properties of ceramic composites at high temperature — Determination of tensile properties▷ISO/CD 14705 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for hardness of monolithic ceramics at room temperature▷ISO/WD 15733 Fine ceramics (advanced ceramics, advanced technical ceramics) — Mechanical properties of ceramic composites at ambient temperature in air atmospheric pressure — Determination of tensile properties▷ISO/AWI 17138 Fine ceramics (advanced ceramics, advanced technical ceramics) — Mechanical properties of ceramic composites at room temperature — Determination of flexural strength▷ISO/AWI 17561 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test methods for dynamic elastic moduli of monolithic ceramics at room temperature by sonic resonance and Impulse Excitation Technique (IET)▷ISO/CD 17590 Fine ceramics (advanced ceramics, advanced technical ceramics) — Methods of tests for reinforcements — Determination of the tensile properties of ceramic filaments at elevated temperature in air using the hot grip technique▷ISO/AWI 17947-1 Fine ceramics (advanced ceramics, advanced technical ceramics) — Methods for chemical analysis of fine silicon nitride powders — Part 1: Wet chemical methods, X-ray fluorescence (XRF) using the fused cast-bead method, carrier-gas hot extraction (CGHE) and combustion methods▷ISO/AWI 18719 Fine ceramics (advanced ceramics, advanced technical ceramics) — Methods for chemical analysis of impurities in yttrium oxide powders using inductively coupled plasma-optical emission spectrometry
-
[특집-기술위원회] TC 205 - 건축 환경 디자인(Building environment design)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~TC 186 △1984년 TC 188 △1985년 TC 189, TC 190, TC 191 △1988년 TC 192~TC 194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 등이 있다.ISO/TC 205 건축 환경 디자인(Building environment design)과 관련된 기술위원회는 TC 204와 마찬가지로 1992년 결성됐다. 사무국은 미국 표준협회(American National Standards Institute, ANSI)에서 맡고 있다.위원회는 라이언 섄리(Mr Ryan Shanley)가 책임지고 있다. 현재 의장은 드레이크 에르베(Mr Drake Erbe)이며 임기는 2025년말 까지다.ISO 기술 프로그램 관리자는 스테판 소바쥬(M Stéphane Sauvage), ISO 편집 관리자는 클라우디아 루에제(Ms Claudia Lueje) 등이다.범위는 수용 가능한 실내 환경 및 실행 가능한 에너지 절약, 효율성을 위해 신규 건물의 설계 및 기존 건물 개조에 관한 표준화다.건축 환경 설계는 기술적 건축 시스템 및 관련 건축 측면을 다루며 관련 설계 프로세스, 설계 방법, 설계 결과 및 설계 단계 건물 커미셔닝을 포함하고 있다. 실내 환경에는 공기질과 열, 음향, 시각적 요소가 포함된다. 다음 내용들도 표준화에 포함된다.세부적으로 보면 △건물 설계 및 기존 건물 개조 설계에서 다룰 수 있는 실내 환경 품질 및 에너지와 관련된 지속 가능성 측면 △건축 환경 설계의 일반 원칙 △에너지 효율적인 건물 설계 △건물 및 개조 설계의 건물 자동화 및 제어 시스템 △건물 및 개조 설계의 실내 공기질 △건물의 실내 열 환경 및 개조 설계 △건물 및 개조 설계의 실내 음향 환경 △건물의 실내 시각적 환경 및 개조 설계 △복사를 포함한 냉난방 시스템 설계 △새 건물 및 개조 설계에 건물 환경 장비의 성능을 테스트하고 평가하는 방법의 적용 등이다.전체적인 접근 방식을 사용하는 ISO/TC163/WG4 공동 작업 그룹 TC 163 및 TC 205 에너지 성능 ISO/TC163/WG4 Joint working group TC 163 & TC 205 Energy performance)을 통해 ISO/TC 163과의 긴밀한 협력을 통해 건물 개조 뿐 아니라 신규 및 기존 건물의 에너지 성능에 관한 전체적인 평가의 표준화도 포함된다.표준화에는 △용어 및 정의 △건물 및 기술 시스템의 시스템 경계 △건축 요소의 에너지 성능을 고려한 건물의 전반적인 에너지 성능 평가 △건물 관련 시스템(난방, 냉방, 가정용 온수, 환기, 조명, 시스템 제어, 운송 및 기타 에너지 관련 시스템) △실내 및 실외 조건 △지역 에너지 생산(현장 및 지역 수준) △(사용) 에너지원(재생 가능 포함) △건물 커미셔닝 △전반적인 에너지 효율 평가 △건축물의 에너지 성능 및 에너지 성능 인증을 나타내는 수단 등이 있다.다만 △기타 인체공학적 요인 △대기 오염물질과 열, 음향 및 조명 특성을 측정하는 방법 △건축 환경의 열 성능 및 에너지 사용(ISO TC 163) △기존 건물의 건물 환경 장비 성능 및 등급을 테스트하는 방법 △기존 건물을 검사하거나 평가 △건설 등은 제외한다.현재 ISO/TC 205 사무국의 직접적인 책임 하에 발행된 표준은 49개며 ISO/TC 205 사무국의 직접적인 책임하에 개발 중인 표준은 10개다. 참여하고 있는 회원은 26개국, 참관 회원은 34개국이다.□ ISO/TC 205 사무국의 직접적인 책임 하에 발행된 표준 49개 중 15개 목록▷ISO 11855-1:2021 Building environment design — Embedded radiant heating and cooling systems — Part 1: Definitions, symbols, and comfort criteria▷ISO 11855-1:2021/Amd 1:2023 Building environment design — Embedded radiant heating and cooling systems — Part 1: Definitions, symbols, and comfort criteria — Amendment 1▷ISO 11855-2:2021 Building environment design — Embedded radiant heating and cooling systems — Part 2: Determination of the design heating and cooling capacity▷ISO 11855-2:2021/Amd 1:2023 Building environment design — Embedded radiant heating and cooling systems — Part 2: Determination of the design heating and cooling capacity — Amendment 1▷ISO 11855-3:2021 Building environment design — Embedded radiant heating and cooling systems — Part 3: Design and dimensioning▷ISO 11855-3:2021/Amd 1:2023 Building environment design — Embedded radiant heating and cooling systems — Part 3: Design and dimensioning — Amendment 1▷ISO 11855-4:2021 Building environment design — Embedded radiant heating and cooling systems — Part 4: Dimensioning and calculation of the dynamic heating and cooling capacity of Thermo Active Building Systems (TABS)▷ISO 11855-4:2021/Amd 1:2023 Building environment design — Embedded radiant heating and cooling systems — Part 4: Dimensioning and calculation of the dynamic heating and cooling capacity of Thermo Active Building Systems (TABS) — Amendment 1▷ISO 11855-5:2021 Building environment design — Embedded radiant heating and cooling systems — Part 5: Installation▷ISO 11855-5:2021/Amd 1:2023 Building environment design — Embedded radiant heating and cooling systems — Part 5: Installation — Amendment 1▷ISO 11855-6:2018 Building environment design — Design, dimensioning, installation and control of embedded radiant heating and cooling systems — Part 6: Control▷ISO 11855-6:2018/Amd 1:2023 Building environment design — Design, dimensioning, installation and control of embedded radiant heating and cooling systems — Part 6: Control — Amendment 1▷ISO 11855-7:2019 Building environment design — Design, dimensioning, installation and control of embedded radiant heating and cooling systems — Part 7: Input parameters for the energy calculation▷ISO 11855-7:2019/Amd 1:2024 Building environment design — Design, dimensioning, installation and control of embedded radiant heating and cooling systems — Part 7: Input parameters for the energy calculation — Amendment 1▷ISO 11855-8:2023 Building environment design — Design, dimensioning, installation and control of embedded radiant heating and cooling systems — Part 8: Electrical heating systems□ ISO/TC 205 사무국의 직접적인 책임 하에 개발 중인 표준 10개 목록▷ISO/TR 5863 Integrative design of the building envelope — General principles▷ISO/DIS 16484-2 Building automation and control systems (BACS) — Part 2: Hardware▷ISO/DIS 16484-4 Building automation and control systems (BACS) — Part 4: Control applications▷ISO/DIS 16813 Building environment design — Indoor environment — General principles▷ISO/WD 20734 Building Enviroment Design — Daylighting design procedure for indoor visual environment▷ISO/WD 21075 Design and assessment process of whole-building mechanical ventilation systems in residential buildings▷ISO/WD 22511-1 Design process of ventilative cooling systems — Part 1: Non-residential buildings▷ISO/AWI TS 23764 Methodology for achieving non-residential zero-energy buildings (ZEBs)▷ISO/CD 24359-1 Building commissioning process planning — Part 1: New buildings▷ISO/AWI TR 52032-2 Energy performance of buildings — Energy requirements and efficiencies of heating, cooling and domestic hot water (DHW) distribution systems — Part 2: Explanation and justification of ISO 52032-1
-
[특집-기술위원회] TC 204 - 지능형 교통시스템(Intelligent transport systems)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~TC 186 △1984년 TC 188 △1985년 TC 189, TC 190, TC 191 △1988년 TC 192~TC 194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 등이 있다.ISO/TC 204 지능형 교통시스템(Intelligent transport systems)과 관련된 기술위원회는 1992년 결성됐다. 사무국은 미국 표준협회(American National Standards Institute, ANSI)에서 맡고 있다.위원회는 제니퍼 콜린스(Ms Jennifer Collins)가 책임지고 있다. 현재 의장은 쿠로시 올리아이(Mr Koorosh Olyai)이며 임기는 2025년말 까지다.ISO 기술 프로그램 관리자는 하킴 음킨시(Mr Hakim Mkinsi), ISO 편집 관리자는 앨리슨 레이드 자몬드(Ms Alison Reid-Jamond) 등이다.범위는 도시 및 농촌 지상 교통 분야의 정보, 통신 및 제어 시스템 표준화다. 표준화에는 인터모달 및 멀티모달 측면, 여행자 정보, 교통 관리, 대중 교통, 상업 교통, 긴급 서비스, 지능형 교통 시스템(intelligent transport systems, ITS) 분야 상업 서비스 등을 포함하고 있다. 단, 차량 내 운송 정보 및 제어 시스템(ISO/TC 22)은 제외한다.참고로 ISO/TC 204는 지능형 교통 시스템(ITS)의 전반적인 시스템 측면과 인프라 측면을 담당하고 있다. 기존 국제 표준화 기관의 작업을 고려한 표준 개발 일정을 포함해 이 분야의 전반적인 ISO 작업 프로그램을 조정하고 있다.현재 ISO/TC 204 사무국의 직접적인 책임 하에 발행된 표준은 338개며 ISO/TC 204 사무국의 직접적인 책임하에 개발 중인 표준은 67개다. 참여하고 있는 회원은 33개국, 참관 회원은 28개국이다.□ ISO/TC 204 사무국의 직접적인 책임 하에 발행된 표준 338개 중 15개 목록▷ISO 4272:2022 Intelligent transport systems — Truck platooning systems (TPS) — Functional and operational requirements▷ISO 4273:2024 Intelligent transport systems — Automated braking during low-speed manoeuvring (ABLS) — Requirements and test procedures▷ISO/TR 4286:2021 Intelligent transport systems — Use cases for sharing of probe data▷ISO/TS 4398:2022 Intelligent transport systems — Guided transportation service planning data exchange▷ISO 4426:2021 Intelligent transport systems — Lower layer protocols for usage in the European digital tachograph▷ISO/TR 4445:2021 Intelligent transport systems — Mobility integration — Role model of ITS service application in smart cities▷ISO/TR 4447:2022 Intelligent transport systems — Mobility integration — Comparison of two mainstream integrated mobility concepts▷ISO/TS 5206-1:2023 Intelligent transport systems — Parking — Part 1: Core data model▷ISO/TS 5255-1:2022 Intelligent transport systems — Low-speed automated driving system (LSADS) service — Part 1: Role and functional model▷ISO/TR 5255-2:2023 Intelligent transport systems — Low-speed automated driving system (LSADS) service — Part 2: Gap analysis▷ISO 5345:2022 Intelligent transport systems — Identifiers▷ISO/TR 6026:2022 Electronic fee collection — Pre-study on the use of vehicle licence plate information and automatic number plate recognition (ANPR) technologies▷ISO/TR 7872:2022 Intelligent transport systems — Mobility integration — Digital infrastructure service role and functional model for urban ITS service applications▷ISO/TR 7878:2023Intelligent transport systems — Mobility integration — Enterprise view▷ISO 10711:2012 Intelligent Transport Systems — Interface Protocol and Message Set Definition between Traffic Signal Controllers and Detectors□ ISO/TC 204 사무국의 직접적인 책임 하에 개발 중인 표준 67개 중 15개 목록▷ISO/CD TR 4448-1 Intelligent transport systems — Public-area Mobile Robots (PMR) — Part 1: Overview of paradigm▷ISO/AWI TS 4448-16 Intelligent transport systems — Public-area Mobile Robots (PMR) — Part 16: 16▷ISO/AWI TS 5087-3 Information technology — City data model — Part 3: Service level concepts -Transportation planning▷ISO/CD TR 6029-1.2 Intelligent transport systems — Seamless positioning for multimodal transportation in ITS stations — Part 1: General information and use case definition▷ISO/AWI 6029-2 Intelligent transport systems — Seamless positioning for multimodal transportation in ITS stations — Part 2: Nomadic and mobile device dataset for positioning data fusion▷ISO/DTS 7815-1 Intelligent transport systems — Telematics applications for regulated commercial freight vehicles (TARV) using ITS stations — Part 1: Secure vehicle interface framework and architecture▷ISO/DTS 7815-2 Intelligent transport systems — Telematics applications for regulated commercial freight vehicles (TARV) using ITS stations — Part 2: Specification of the secure vehicle interface▷ISO/CD 7856 Intelligent transport systems —Remote support for low speed automated driving systems (RS-LSADS) —Performance requirements, system requirements and performance test procedures▷ISO/AWI TR 7874-1 Intelligent transport systems — Mobility integration multimodal pricing — Part 1: Framework▷ISO/AWI 12768-1 Intelligent transport systems — Automated Valet Driving Systems (AVDS) — Part 1: Part 1: Requirements, System Framework, Communication Interfaces and Test Procedures▷ISO/AWI 12768-2 Intelligent transport systems — Automated Valet Driving Systems (AVDS) — Part 2: Part 2: System framework, security procedures and requirements▷ISO/CD TR 12786 Intelligent transport systems — Big data and artificial intelligence supporting intelligent transport systems — Use cases▷ISO 12813 Electronic fee collection — Compliance check communication for autonomous systems▷ISO/AWI 12855 Electronic fee collection — Information exchange between service provision and toll charging▷ISO/AWI 13140 Electronic fee collection -– Conformity evaluation of on-board and roadside equipment to ISO 13141
-
[특집-기술위원회] TC 201 - 표면 화학 분석(Surface chemical analysis)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~TC 186 △1984년 TC 188 △1985년 TC 189, TC 190, TC 191 △1988년 TC 192~TC 194 △1989년 TC 195 △1990년 TC 197, TC 198 등이 있다.ISO/TC 201 표면 화학 분석(Surface chemical analysis)과 관련된 기술위원회는 TC 199와 마찬가지로 1991년 결성됐다. 사무국은 일본 산업표준조사회(日本産業標準調査会, Japanese Industrial Standards Committee, JISC)에서 맡고 있다.위원회는 사토시 곤다(Dr Satoshi Gonda)가 책임지고 있다. 현재 의장은 히데히코 노나카(Dr Hidehiko Nonaka)이다.ISO 기술 프로그램 관리자는 주안우 주(Ms Chuanyu Zou), ISO 편집 관리자는 아룬 ABY 파라에카티(Mr Arun ABY Paraecattil) 등이다.범위는 표면 화학 분석 분야의 표준화다. 표면 화학 분석에는 전자, 이온, 중성 원자 또는 분자, 광자의 빔이 시료 재료에 입사되어 산란되거나 방출된 전자, 이온, 중성 원자 또는 분자, 광자가 감지되는 분석 기술이 포함된다.또한 표면 위로 스캔하는 조사 및 표면 관련 신호를 감지하는 기술도 포함하지만 ISO/TC 202의 범위 내에 있는 주사전자현미경은 제외한다.참고로 현재 표면 화학 분석 기술을 사용하면 분석 정보는 표면에서 가까운 영역(일반적으로 20 nm 이내)의 정보를 얻을 수 있다. 분석 정보 대비 깊이 데이터(analytical information-versus-depth data)는 더 깊은 표면 분석 기술을 사용해 얻을 수 있다.현재 ISO/TC 201 사무국과 관련해 발행된 표준은 81개며 ISO/TC 201 사무국의 직접적인 책임 하에 발행된 표준은 8개다.ISO/TC 201 사무국과 관련해 개발 중인 표준은 22개며 ISO/TC 201 사무국의 직접적인 책임 하에 개발 중인 표준은 2개다. 참여하고 있는 회원은 13개국, 참관 회원은 12개국이다.□ ISO/TC 201 사무국의 직접적인 책임 하에 발행된 표준 8개 목록▷ISO 14706:2014 Surface chemical analysis — Determination of surface elemental contamination on silicon wafers by total-reflection X-ray fluorescence (TXRF) spectroscopy▷ISO 16413:2020 Evaluation of thickness, density and interface width of thin films by X-ray reflectometry — Instrumental requirements, alignment and positioning, data collection, data analysis and reporting▷ISO 17331:2004 Surface chemical analysis — Chemical methods for the collection of elements from the surface of silicon-wafer working reference materials and their determination by total-reflection X-ray fluorescence (TXRF) spectroscopy▷ISO 17331:2004/Amd 1:2010 Surface chemical analysis — Chemical methods for the collection of elements from the surface of silicon-wafer working reference materials and their determination by total-reflection X-ray fluorescence (TXRF) spectroscopy — Amendment 1▷ISO 18337:2015 Surface chemical analysis — Surface characterization — Measurement of the lateral resolution of a confocal fluorescence microscope▷ISO/TS 18507:2015 Surface chemical analysis — Use of Total Reflection X-ray Fluorescence spectroscopy in biological and environmental analysis▷ISO/TR 19693:2018 Surface chemical analysis — Characterization of functional glass substrates for biosensing applications▷ISO 24465:2023 Surface chemical analysis — Determination of the minimum detectability of surface plasmon resonance device□ ISO/TC 201 사무국의 직접적인 책임 하에 개발 중인 표준 2개 목록▷ISO/AWI TR 4550 SCA –Surface chemical analysis of bacteria and biofilms▷ISO/FDIS 23124 Surface chemical analysis — Measurement of lateral and axial resolutions of a Raman microscope□ ISO/TC 201 사무국 분과위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 201/SC 1 Terminology ; 발행된 표준 3개, 개발 중인 표준 0개▷ISO/TC 201/SC 2 General procedures ; 발행된 표준 9개, 개발 중인 표준 2개▷ISO/TC 201/SC 3 Data management and treatment ; 발행된 표준 5개, 개발 중인 표준 1개▷ISO/TC 201/SC 4 Depth profiling ; 발행된 표준 6개, 개발 중인 표준 0개▷ISO/TC 201/SC 6 Secondary ion mass spectrometry ; 발행된 표준 12개, 개발 중인 표준 2개▷ISO/TC 201/SC 7 Electron spectroscopies ; 발행된 표준 23개, 개발 중인 표준 5개 ▷ISO/TC 201/SC 8 Glow discharge spectroscopy ; 발행된 표준 6개, 개발 중인 표준 3개▷ISO/TC 201/SC 9 Scanning probe microscopy ; 발행된 표준 8개, 개발 중인 표준 4개▷ISO/TC 201/SC 10 X-ray Reflectometry (XRR) and X-ray Fluorescence (XRF) Analysis ; 발행된 표준 1개, 개발 중인 표준 3개
-
[특집-기술위원회] TC 198 - 보건 의료 제품의 멸균(Sterilization of health care products)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~TC 186 △1984년 TC 188 △1985년 TC 189, TC 190, TC 191 △1988년 TC 192~TC 194 △1989년 TC 195 등이 있다.ISO/TC 198 보건 의료 제품의 멸균(Sterilization of health care products)과 관련된 기술위원회는 TC 197과 마찬가지로 1990년 결성됐다. 사무국은 미국 표준협회(American National Standards Institute, ANSI)에서 맡고 있다.위원회는 아만다 베네딕(Ms Amanda Benedict)가 책임지고 있다. 현재 의장은 리차드 밴크로프트(Mr Richard Bancroft)이며 임기는 2025년 말까지다.ISO 기술 프로그램 관리자는 페트리샤 쿡(Mme Patricia Cook), ISO 편집 관리자는 클라우디아 루에제(Ms Claudia Lueje)등이다. 범위는 보건의료 제품의 멸균을 위한 프로세스 및 장비의 표준화다.현재 ISO/TC 198 사무국의 직접적인 책임 하에 발행된 표준은 69개며 ISO/TC 198 사무국의 직접적인 책임 하에 개발 중인 표준은 15개다. 참여하고 있는 회원은 34개국, 참관 회원은 21개국이다.□ ISO/TC 198 사무국의 직접적인 책임 하에 발행된 표준 69개 중 15개 목록▷ISO/TS 5111:2022 Guidance on quality of water for sterilizers, sterilization and washer-disinfectors for health care products▷ISO 11135:2014 Sterilization of health-care products — Ethylene oxide — Requirements for the development, validation and routine control of a sterilization process for medical devices▷ISO 11135:2014/Amd 1:2018 Sterilization of health-care products — Ethylene oxide — Requirements for the development, validation and routine control of a sterilization process for medical devices — Amendment 1: Revision of Annex E, Single batch release▷ISO 11137-1:2006 Sterilization of health care products — Radiation — Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices▷ISO 11137-1:2006/Amd 1:2013 Sterilization of health care products — Radiation — Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices — Amendment 1▷ISO 11137-1:2006/Amd 2:2018 Sterilization of health care products — Radiation — Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices — Amendment 2: Revision to 4.3.4 and 11.2▷ISO 11137-2:2013 Sterilization of health care products — Radiation — Part 2: Establishing the sterilization dose▷ISO 11137-2:2013/Amd 1:2022 Sterilization of health care products — Radiation — Part 2: Establishing the sterilization dose — Amendment 1▷ISO 11137-3:2017 Sterilization of health care products — Radiation — Part 3: Guidance on dosimetric aspects of development, validation and routine control▷ISO/TS 11137-4:2020 Sterilization of health care products — Radiation — Part 4: Guidance on process control▷ISO 11138-1:2017 Sterilization of health care products — Biological indicators — Part 1: General requirements▷ISO 11138-2:2017 Sterilization of health care products — Biological indicators — Part 2: Biological indicators for ethylene oxide sterilization processes▷ISO 11138-3:2017 Sterilization of health care products — Biological indicators — Part 3: Biological indicators for moist heat sterilization processes▷ISO 11138-4:2017 Sterilization of health care products — Biological indicators — Part 4: Biological indicators for dry heat sterilization processes▷ISO 11138-5:2017 Sterilization of health care products — Biological indicators — Part 5: Biological indicators for low-temperature steam and formaldehyde sterilization processes□ ISO/TC 198 사무국의 직접적인 책임 하에 개발 중인 표준 15개 목록▷ISO/DIS 11135.2 Sterilization of health care products — Ethylene oxide — Requirements for the development, validation and routine control of a sterilization process for medical devices▷ISO/FDIS 11137-1 Sterilization of health care products — Radiation — Part 1: Requirements for the development, validation and routine control of a sterilization process for medical devices▷ISO/CD 11140-3 Sterilization of health care products — Chemical indicators — Part 3: Class 2 indicator systems for use in the Bowie and Dick-type steam penetration test▷ISO/CD 11140-4 Sterilization of health care products — Chemical indicators — Part 4: Class 2 indicators as an alternative to the Bowie and Dick-type test for detection of steam penetration▷ISO/CD 11140-5 Sterilization of health care products — Chemical indicators — Part 5: Class 2 indicators for Bowie and Dick-type air removal tests▷ISO/AWI 11607-3 Packaging for terminally sterilized medical devices — Part 3: Requirements for process development for forming, sealing and assembly▷ISO/AWI 11737-1 Sterilization of health care products — Microbiological methods — Part 1: Determination of a population of microorganisms on products▷ISO/FDIS 15883-1 Washer-disinfectors — Part 1: General requirements, terms and definitions and tests▷ISO/DIS 15883-2 Washer-disinfectors — Part 2: Requirements and tests for washer-disinfectors employing thermal disinfection for critical and semi-critical medical devices▷ISO/DIS 15883-3 Washer-disinfectors — Part 3: Requirements and tests for washer-disinfectors employing thermal disinfection for human waste containers▷ISO/CD 15883-6 Washer-disinfectors — Part 6: Requirements and tests for washer-disinfectors employing thermal disinfection for noncritical medical devices and health care equipment▷ISO/DIS 15883-7 Washer-disinfectors — Part 7: Requirements and tests for washer-disinfectors employing chemical disinfection for non-critical thermolabile medical devices and health care equipment▷ISO/AWI TS 17664-3 Processing of health care products — Information to be provided by the medical device manufacturer for the processing of medical devices — Part 3: Guidance on the designation of a reusable medical device to a quantitative cleaning classification▷ISO 17665 Sterilization of health care products — Moist heat — Requirements for the development, validation and routine control of a sterilization process for medical devices▷ISO/AWI 19253 Sterilization of health care products — Application of ISO/TS 22421 to the requirements for sterilizers used for the terminal sterilization of health care products containing aqueous liquid in sealed containers
-
[특집-기술위원회] TC 194 - 의료 장비의 생물학적 및 임상적 평가(Biological and clinical evaluation of medical devices)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~TC 186 △1984년 TC 188 △1985년 TC 189, TC 190, TC 191 등이 있다.ISO/TC 194 의료 장비의 생물학적 및 임상적 평가(Biological and clinical evaluation of medical devices)와 관련된 기술위원회는 TC 192, TC 193과 마찬가지로 1988년 결성됐다. 사무국은 독일 표준화기구(Deutsches Institut für Normung e.V., DIN)에서 맡고 있다.위원회는 수잔 민크위츠(Mrs Dr Susann Minkwitz)가 책임지고 있다. 현재 의장은 제레미 팅클러(Mr Jeremy Tinkler)이며 임기는 2026년 말까지다. ISO 기술 프로그램 관리자는 패트리샤 쿡(Mme Patricia Cook), ISO 편집 관리자는 산잘리 자인(Ms Sanjali Jain)등이다.범위는 해당 장치의 인간 임상 조사에 대한 우수 임상 실습 원칙 뿐 아니라 해당 재료 및 장치에 적용 가능한 생물학적 테스트 방법과 함께 의료 및 치과 재료 및 장치의 생물학적 및 임상 평가에 대한 접근 방식의 표준화다.현재 ISO/TC 194 사무국의 직접적인 책임 하에 발행된 표준은 37개 ISO/TC 194 사무국의 직접적인 책임 하에 개발 중인 표준은 16개다. 참여하고 있는 회원은 33개국, 참관 회원은 19개국이다.□ ISO/TC 194 사무국의 직접적인 책임 하에 발행된 표준 37개 중 15개 목록▷ISO 10993-1:2018 Biological evaluation of medical devices — Part 1: Evaluation and testing within a risk management process▷ISO 10993-2:2022 Biological evaluation of medical devices — Part 2: Animal welfare requirements▷ISO 10993-3:2014 Biological evaluation of medical devices — Part 3: Tests for genotoxicity, carcinogenicity and reproductive toxicity▷ISO 10993-4:2017 Biological evaluation of medical devices — Part 4: Selection of tests for interactions with blood▷ISO 10993-5:2009 Biological evaluation of medical devices — Part 5: Tests for in vitro cytotoxicity▷ISO 10993-6:2016 Biological evaluation of medical devices — Part 6: Tests for local effects after implantation▷ISO 10993-7:2008 Biological evaluation of medical devices — Part 7: Ethylene oxide sterilization residuals▷ISO 10993-7:2008/Amd 1:2019 Biological evaluation of medical devices — Part 7: Ethylene oxide sterilization residuals — Amendment 1: Applicability of allowable limits for neonates and infants▷ISO 10993-7:2008/Cor 1:2009 Biological evaluation of medical devices — Part 7: Ethylene oxide sterilization residuals — Technical Corrigendum 1▷ISO 10993-9:2019 Biological evaluation of medical devices — Part 9: Framework for identification and quantification of potential degradation products▷ISO 10993-10:2021 Biological evaluation of medical devices — Part 10: Tests for skin sensitization▷ISO 10993-11:2017 Biological evaluation of medical devices — Part 11: Tests for systemic toxicity▷ISO 10993-12:2021 Biological evaluation of medical devices — Part 12: Sample preparation and reference materials▷ISO 10993-13:2010 Biological evaluation of medical devices — Part 13: Identification and quantification of degradation products from polymeric medical devices▷ISO 10993-14:2001 Biological evaluation of medical devices — Part 14: Identification and quantification of degradation products from ceramics□ ISO/TC 194 사무국의 직접적인 책임 하에 개발 중인 표준 16개 목록▷ISO/CD 8250 Cleanliness of medical devices — Process design and test methods▷ISO/CD 10993-1.2 Biological evaluation of medical devices — Part 1: Requirements and general principles for the evaluation of biological safety within a risk management process▷ISO/AWI 10993-2 Biological evaluation of medical devices — Part 2: Animal welfare requirements▷ISO/AWI 10993-3 Biological evaluation of medical devices — Part 3: Tests for genotoxicity, carcinogenicity and reproductive toxicity▷ISO 10993-4:2017/DAmd 1 Biological evaluation of medical devices — Part 4: Selection of tests for interactions with blood — Amendment 1▷ISO/CD 10993-6 Biological evaluation of medical devices — Part 6: Tests for local effects after implantation▷ISO/CD 10993-7.2 Biological evaluation of medical devices — Part 7: Ethylene oxide sterilization residuals▷ISO/CD 10993-11 Biological evaluation of medical devices — Part 11: Tests for systemic toxicity▷ISO 10993-12:2021/AWI Amd 1 Biological evaluation of medical devices — Part 12: Sample preparation and reference materials — Amendment 1▷ISO/AWI 10993-16 Biological evaluation of medical devices — Part 16: Toxicokinetic study design for degradation products and leachables▷ISO 10993-17:2023/AWI Amd 1 Biological evaluation of medical devices — Part 17: Toxicological risk assessment of medical device constituents — Amendment 1▷ISO 10993-23:2021/AWI Amd 1 Biological evaluation of medical devices — Part 23: Tests for irritation — Amendment 1▷ISO/CD 14155 Clinical investigation of medical devices for human subjects — Good clinical practice▷ISO/AWI 18969 Clinical evaluation of medical devices▷ISO/AWI 21762 Medical devices utilizing human tissues and their derivatives — Application of risk management▷ISO/AWI TR 24850 Sources of hazard information for medical device constituents